Formula 1
FIA presents proposals to TWG
The FIA has presented the Technical Working Group (TWG) with three sets of proposals to consider for regulation changes aimed at reducing the performance of Formula One cars in the future. The proposals deal with aerodynamics, bodywork and ...
Published: Sep 7, 2004, 5:38 PM
Copy link
Share on Viber
The FIA has presented the Technical Working Group (TWG) with three sets of proposals to consider for regulation changes aimed at reducing the performance of Formula One cars in the future. The proposals deal with aerodynamics, bodywork and engines.
The FIA is willing to consider a combination of regulations from the packages presented, if the TWG and the F1 Commission agree. The sport's governing body also asked for two other safety matters to be considered:
- the elimination of materials likely to leave sharp shards on the circuit in the event of an accident;
- a reduction in the weight limit sufficient to eliminate ballast (at least on most of the cars) in order to reduce the energy to be dissipated if control of a car is lost. This would be combined, if necessary, with a change in relative wheel widths front to rear.
The TWG was due to meet today (September 6th) to discuss the proposals and FIA President Max Mosley is scheduled to appear at Friday's press conference at the Italian Grand Prix.
The FIA packages are as follows -- italics in brackets show the previously proposed measurements:
Package 1 consists of the FIA's suggestions for Sporting and Technical Regulations dated 16 July 2004 with the following differences:
1) The following amendments will be made to Article 3:
3.7 Front bodywork height:
3.7.1 All bodywork situated forward of a point lying 330mm behind the front wheel centre line, and more than 250mm from the centre line of the car, must be no less than 100mm (150mm) and no more than 300mm (350mm) above the reference plane.
Furthermore, all bodywork situated forward of a point lying 330mm in front of the front wheel centre line, and more than 250mm from the centre line of the car, must be no less than 150mm and no more than 350mm above the reference plane.
3.7.2 All bodywork situated forward of a point lying 330mm in front of the front wheel centre line must be no less than 50mm above the reference plane.
2) Additional constraints will be placed on engines in 2006 : - The cylinder bore will be fixed - The cylinder spacing and engine length will be fixed - The crankshaft centre line height will be fixed - The engine mounting points front and rear will be fixed
Package 2 consists of the FIA's suggestions for Sporting and Technical Regulations dated 16 July 2004 with the following amendments to Article 3 :
3.9 Bodywork between the rear wheels:
3.9.1 No bodywork more than 100mm from the car centre line, and which is situated between the rear wheel centre line and a point lying 330mm forward of it, may be more than 600mm above the reference plane.
3.9.2 No bodywork between 75mm and 480mm (more than 50mm) from the car centre line, and which is situated between the rear wheel centre line and a point lying 150mm behind it, may be located between 375mm and 600mm (more than 450mm) above the reference plane.
3.10 Height behind the rear wheel centre line:
3.10.1 Any part of the car behind the centre line of the rear wheels must not be more than 800mm above the reference plane.
3.10.2 No bodywork behind the centre line of the rear wheels, and more than 150mm each side of the longitudinal centre line of the car, may be less than 300mm above the reference plane.
3.10.3 Any bodywork more than 150mm behind the rear wheel centre line which is between 300mm and 600mm above the reference plane, and between 75mm and 480mm from the car centre line, must lie in an area when viewed from the side of the car that is situated between 300mm and 375mm above the reference plane and between 150mm and 500mm behind the rear wheel centre line.
When viewed from the side of the car no longitudinal cross section may have more than one closed section in the lower area. Any bodywork behind the rear wheel centre line which is more than 375mm (600mm) above the reference plane, and between 75mm and 480mm from the car centre line, must lie in an area when viewed from the side of the car that is situated between 600mm and 800mm above the reference plane and between the rear wheel centre line and a point 350mm behind it.
When viewed from the side of the car, no longitudinal cross section may have more than two closed sections in the upper area. Furthermore, the distance between adjacent sections at any longitudinal plane must not exceed 15mm at their closest position. In side view, the projected area of any bodywork lying between 300mm and 800mm above the reference plane and between the rear wheel centre line and a point 600mm behind it must be greater than 230000mm².
3.17.2 Bodywork may deflect no more than 10mm vertically when a 500N load is applied vertically to it 450mm (400mm) forward of the rear wheel centre line and 650mm from the car centre line. The load will be applied in a downward direction using a 50mm diameter ram and an adapter of the same size. Teams must supply the latter when such a test is deemed necessary.
Package 3 consists of the FIA's suggestions for Sporting and Technical Regulations dated 16 July 2004 with the following differences for application in 2006:
1) The car reference plane will be required to extend as far forward as the front wheel centre line.
2) All turning vanes and barge boards will be forbidden.
3) The only changes to Article 5 will be the following:
5.1 Engine specification:
5.1.1 Only 4-stroke engines with reciprocating pistons are permitted.
5.1.2 Engine capacity must not exceed 2400 cc.
5.1.3 Supercharging is forbidden.
5.1.4 All engines must have 8 cylinders and the normal section of each cylinder must be circular.
5.1.5 Engines may have no more than 5 valves per cylinder.
5.2 Other means of propulsion:
5.2.1 The use of any device, other than the 2.4 litre, four stroke engine described in 5.1 above, to power the car, is not permitted.
5.2.2 The total amount of recoverable energy stored on the car must not exceed 300kJ, any which may be recovered at a rate greater than 2kW must not exceed 20kJ.
Note:
To be accompanied by a sporting rule that no team may use an engine which is not available free of charge and on a fully competitive basis to a number of other teams equal to or greater than the number of teams entered in the Championship divided by the number of different makes of engine in use, rounded up to the nearest whole number.
The supplier of each such engine (or its parent company when deemed appropriate by the FIA) would be required to give a binding undertaking to the FIA that it would not cease supply without first giving written notice during the year preceding its last full year of participation.
We want your opinion!
What would you like to see on Motorsport.com?
Take our 5 minute survey.
- The Motorsport.com Team
Read and post comments
Read also :
Share Or Save This Story
Copy link
Share on Viber
Previous article Italian GP: Sauber preview
Next article Button confident of Williams move
Top Comments
There are no comments at the moment. Would you like to write one?
View More & Comment
Latest news
George Russell: F1 2026 season a test of "character and resilience"
Formula 1
F1 Formula 1
United States GP
33 min
George Russell: F1 2026 season a test of "character and resilience"
Marc Marquez: ‘Jorge Martin rides on instinct; he just attacks, and that’s his strength’
MotoGP
MGP MotoGP
Australian GP
1 h
Marc Marquez: ‘Jorge Martin rides on instinct; he just attacks, and that’s his strength’
Lamborghini Super Trofeo | North America, Race 2: Bamber dominates to take the win
Lamborghini Super Trofeo
LBST Lamborghini Super Trofeo
World Finals - Monza 2026
1 h
Lamborghini Super Trofeo | North America, Race 2: Bamber dominates to take the win
Belgian firm to take over Renault/Alpine engine facility in Viry
WEC
WEC WEC 2 h
Belgian firm to take over Renault/Alpine engine facility in Viry
Feature
Discover prime content
Subscribe and access Motorsport.com with your ad-blocker.
From Formula 1 to MotoGP we report straight from the paddock because we love our sport, just like you. In order to keep delivering our expert journalism, our website uses advertising. Still, we want to give you the opportunity to enjoy an ad-free and tracker-free website and to continue using your adblocker.
You have 2 options:
- Become a subscriber.
- Disable your adblocker.
Subscribe now Already subscribed? Sign in here
Already disabled your adblocker?
Reload page
Manage Alerts
Subscribe