Analysis
Formula 1
Mercedes: Assessing a power unit failure
Step by step procedures on investigation of an engine failure.
Edited: Apr 27, 2016, 12:34 PM
Copy link
Share on Viber
What do we now know about the failure on Lewis' Power Unit in Shanghai?
The Power Unit in question arrived back at Brixworth in the early hours of Thursday morning of the week following the race and investigation into the failure has been on-going every minute since its return to the factory. The MGU-H has been stripped and the issue is suspected to be associated with the insulation. The turbocharger will be replaced in addition to the oil pumps, after debris was found in the oil system. With the repairs completed, this Power Unit will remain in the driver pool and travel to Sochi as a spare.
What's the initial course of action when a Power Unit failure occurs at the track?
First and foremost, a group of engineers at the circuit and a much larger group at Brixworth will pore through readings from the data logger, noting what every sensor on the Power Unit has recorded. That's an instant check which will quickly establish the severity of the problem.
What happens if a major fault is discovered?
If it's then determined that there is an issue which cannot be fixed at the track and hardware needs to be removed, the trackside technicians will ready the components for transport back to Brixworth as quickly as possible. The engineer responsible for the system suspected to be at the core of the issue will subsequently draw up a strip request instruction while the components are in transit.
What exactly does a strip request instruction involve?
It's a detailed sequence of instructions for the technicians working in the build department back at Brixworth, which outlines who will be allocated to each individual stage of the process, what specialist equipment and / or inspection techniques are required and which procedures need to be carried out. The list is written in chronological order with approximate time frames for each step to create a carefully considered timing plan that's fully resourced.
Where do the technicians begin when deconstructing a failed component?
In most cases, the technicians will start by back-flushing oil through the various galleries and filters of the oil and coolant systems to collect any fine debris. While larger fragments can be removed by hand, the finer debris - which often points to the start of the problem - can settle at the end of blind galleries or in filters downstream of the failed part.
How is debris analysed?
Microscope analysis of the debris is the first stage - looking at the different shapes and sizes present to establish whether it's a case of fine wear or a component which has shattered into small pieces. The debris will then be scanned with an electron microscope to check its chemical composition. This helps to establish the material type - which in turn provides an indication of the component that the debris might have come from.
What happens next to the various components in question?
Once the debris analysis has been completed and the components that were involved in the failure have all been stripped, everything is physically laid out to mimic its installed configuration. Looking at the series of components in front of them, what debris has been found and where it ended up, the engineers can begin to establish a likely sequence of events. They will then go back through the logged data from the track to find any step changes in the readings from each Power Unit sensor that might match up to a given theory.
Can virtual simulations be used in the investigation process?
Virtual simulation tools give a good insight into what's going on within a system and are used extensively throughout the development phase. When a component has failed, those models can be referred back to and changes made commensurate with what the team suspects has gone wrong to mimic the cause of the failure.
Does the team ever carry out physical simulations to re-create a failure?
Deliberate errors can be manufactured into hardware, which can then be tested on the dyno in an attempt to replicate a failure. This might be seen as an expensive means of testing - but it's cheaper than having a repeat issue at the circuit. Engines can be run with clearances altered to be either larger or smaller than the typical build standard tolerances - mimicking a scenario in which a surface has become worn, for example.
What about non-mechanical elements of the Power Unit?
Every element of the Power Unit can and will be analysed where necessary. An electrical component such as a PCB (Printed Circuit Board), for example, might be run in an oven at increasing temperatures to establish at what point its semiconductors stop working. This can then be tied in with knowledge about the temperature of that circuit board in the ERS module to establish whether overheating could be diagnosed as a cause of failure.
Who is generally involved in the diagnosis process?
In the first instance, an engineer with expertise in the system concerned will be assigned exclusively to investigating the issue through to its resolution. He or she will chair a meeting at least every 24hrs, calling in four to five people to help cogitate theories. These tend to be people that have a broad experience of the Power Unit, a good problem solving mindset and an ability for lateral thinking - working through theories step by step to ensure they are robust.
Mercedes AMG Petronas
We want your opinion!
What would you like to see on Motorsport.com?
Take our 5 minute survey.
- The Motorsport.com Team
Read and post comments
Read also :
Share Or Save This Story
Copy link
Share on Viber
Previous article Hamilton to re-use China qualifying engine
Next article Williams hopes for a third time lucky in Sochi
Top Comments
There are no comments at the moment. Would you like to write one?
View More & Comment
More from
Lewis Hamilton
‘I’ll try to win, somehow’ – Can Lewis Hamilton and Max Verstappen fight back for F1 Brazilian GP victory?
Formula 1
Formula 1
Sao Paulo GP
‘I’ll try to win, somehow’ – Can Lewis Hamilton and Max Verstappen fight back for F1 Brazilian GP victory?
F1 Brazilian GP: Sunday schedule, weather forecast and how to watch
Formula 1
Formula 1
Sao Paulo GP
F1 Brazilian GP: Sunday schedule, weather forecast and how to watch
More from
Mercedes
George Russell has lost 90 points to Max Verstappen in F1 2026 runner-up battle
Formula 1
Formula 1
Sao Paulo GP
12 h
George Russell has lost 90 points to Max Verstappen in F1 2026 runner-up battle
Charles Leclerc penalised for Liam Lawson clash; Kimi Antonelli and Oliver Bearman also punished after F1 Brazilian GP
Formula 1
Formula 1
Sao Paulo GP
Charles Leclerc penalised for Liam Lawson clash; Kimi Antonelli and Oliver Bearman also punished after F1 Brazilian GP
Latest news
Alex Bowman hits out at critics in snarky post, shooting down early exit rumors
NASCAR Cup
NAS NASCAR Cup
Homestead-Miami
8 h
Alex Bowman hits out at critics in snarky post, shooting down early exit rumors
Ryan Blaney gets sweet redemption after 'nightmares' following 2024 Homestead loss
NASCAR Cup
NAS NASCAR Cup
Homestead-Miami
8 h
Ryan Blaney gets sweet redemption after 'nightmares' following 2024 Homestead loss
IndyCar 2026 season review: Dale Coyne Racing
IndyCar
Indy IndyCar 9 h
IndyCar 2026 season review: Dale Coyne Racing
Noah Gragson apologizes to Daniel Suarez for spinning him at Homestead
NASCAR Cup
NAS NASCAR Cup
Homestead-Miami
9 h
Noah Gragson apologizes to Daniel Suarez for spinning him at Homestead
Feature
Discover prime content
Subscribe and access Motorsport.com with your ad-blocker.
From Formula 1 to MotoGP we report straight from the paddock because we love our sport, just like you. In order to keep delivering our expert journalism, our website uses advertising. Still, we want to give you the opportunity to enjoy an ad-free and tracker-free website and to continue using your adblocker.
You have 2 options:
- Become a subscriber.
- Disable your adblocker.
Subscribe now Already subscribed? Sign in here
Already disabled your adblocker?
Reload page
Manage Alerts
Subscribe