Formula 1 Monaco GP

Bottas wheel nut still stuck on Mercedes car after pitstop issue

Mercedes will only be able to remove the wheel nut from Valtteri Bottas’s Formula 1 car upon returning to its factory after his race-ending pitstop issue in Monaco.

Luke Smith

Edited: May 26, 2021, 3:19 PM

Copy link

Share on Viber

Add as a preferred source

Bottas ran second through the opening stint of Sunday’s Monaco Grand Prix, sitting five seconds behind leader Max Verstappen when he came into the pits on Lap 30 to change tyres.

But Mercedes was unable to get the front-right tyre off Bottas’s car, leaving him stuck in the pits. Despite the team’s best efforts, it was forced to retire the car, bringing the Finnish driver’s day to an early end.

Mercedes technical director James Allison explained how the nut had become machined to the axle by the wheel gun, causing it to get stuck.

“If we don’t quite get the pitstop gun cleanly on the nut, then it can chip away at the driving faces of the nut,” Allison said.

“We call it machining the nut. It is a bit like when you take a Phillips head screwdriver, and you don’t get it squarely in the cross of the screwdriver.

“You start to round off the driving face of the screwdriver slots, and then you just simply can’t take the screw out of whatever it is you are trying to take it out of because you have no longer got the driving faces.

“A very similar thing happens with our pitstop nuts if the gun starts spinning and chipping off the driving faces of the wheel nut.

“Given the power of the gun, you can end up with no driving face and you just machine the nut down to a place where there is nothing left to grab a hold of, and that is what we had today.”

Allison revealed that Mercedes was unable to get the wheel nut off the car at all, requiring a high-power drill to make the removal back at the factory.

“We eventually didn’t get the wheel off, it is sat in our garage with the wheel still on it,” Allison said.

“It will have to be ground off, get a Dremel out and painfully slice through the remnants of the wheel nut. We will do that back at the factory.”

Read Also:

Bottas’s retirement cost Mercedes a likely podium finish in Monaco, allowing Red Bull to move into the lead of the constructors’ championship by one point after Lewis Hamilton could only finish seventh.

Mercedes team principal Toto Wolff said that there were “many factors” that contributed to the issue, refusing to put it down to a single error.

“We need to review the design, we need to review the material of our wheel nut, because the mechanics that operate the wheel nuts need to do it in a way that you can’t machine it off,” Wolff said.

“And as a matter of fact, a mechanic that did that is one of the best, and one of the fittest in terms of pitstop speed, that the team has.

“So there are always things coming together. It’s never someone’s fault, it’s always multi-faceted.”

Mercedes' wheel nut design

Wheel nut design on Valtteri Bottas' Mercedes F1 W12

Photo by: Giorgio Piola

The wheel nut design on the Mercedes (pictured above) is not like those fitted on road cars.

Instead, it is custom built and is dome shaped. It features two vertical extensions that are captured by the wheel gun to rotate the nut on and off.

It was these extensions that were machined off during the Bottas stop and meant the gun had nothing to grab on to.

We want your opinion!

What would you like to see on Motorsport.com?

Take our 5 minute survey.

- The Motorsport.com Team

Read and post comments

Share Or Save This Story

Copy link

Share on Viber

Previous article Leclerc driveshaft issue may be unrelated to Q3 crash - Ferrari

Next article Ferrari: Leclerc's driveshaft would have failed with new gearbox

Top Comments

There are no comments at the moment. Would you like to write one?

View More & Comment

Latest news

Ayao Komatsu: Rafael Camara chosen for F1 2027 seat on speed, not Ferrari links

Formula 1

F1 Formula 1

Singapore GP

58 min

Ayao Komatsu: Rafael Camara chosen for F1 2027 seat on speed, not Ferrari links

Did Haas make the correct decision in signing Rafael Camara for F1 2027?

Formula 1

F1 Formula 1

Singapore GP

2 h

Did Haas make the correct decision in signing Rafael Camara for F1 2027?

Frederik Vesti steps up to full-time role as Cadillac Racing details 2027 IMSA lineup

IMSA

IMSA IMSA 2 h

Frederik Vesti steps up to full-time role as Cadillac Racing details 2027 IMSA lineup

Rafael Camara to replace Esteban Ocon at Haas for F1 2027

Formula 1

F1 Formula 1

Singapore GP

3 h

Rafael Camara to replace Esteban Ocon at Haas for F1 2027

Feature

Discover prime content

Laurent Mekies under the microscope: How different is his leadership at Red Bull from Christian Horner?

Formula 1

Singapore GP

By Ronald Vording

Laurent Mekies under the microscope: How different is his leadership at Red Bull from Christian Horner?

Rwanda turns to F1 as it moves forward from a chequered past

Formula 1

By Filip Cleeren

Rwanda turns to F1 as it moves forward from a chequered past

Christian Horner's inside story of how Red Bull built its own F1 engine

Formula 1

By Jake Boxall-Legge

Christian Horner's inside story of how Red Bull built its own F1 engine

Exclusive video: Christian Horner interview on his Red Bull exit, Mercedes rivalry and more

Formula 1

By Autosport

Exclusive video: Christian Horner interview on his Red Bull exit, Mercedes rivalry and more

Subscribe and access Motorsport.com with your ad-blocker.

From Formula 1 to MotoGP we report straight from the paddock because we love our sport, just like you. In order to keep delivering our expert journalism, our website uses advertising. Still, we want to give you the opportunity to enjoy an ad-free and tracker-free website and to continue using your adblocker.

You have 2 options:

Become a subscriber.
Disable your adblocker.

Subscribe now Already subscribed? Sign in here

Already disabled your adblocker?
Reload page

Manage Alerts